From Real Software Documentation
Serial controls are used to perform serial communications.
The Serial control can be instantiated via code since it is not a subclass of Control. This allows you to easily write code that does communications without adding the control to a window.
To set the Baud rate, assign the desired class constant to the Baud property. To get the baud rate, compare the value of the Baud property to the constants in this table.
Setting nonstandard baud rates is supported only on Windows and Mac OS X 10.4 and above. On OS X 10.4 and higher, the system supports arbitrary baud rates by passing the request along to the driver. If the driver supports the passed baud rate, then it is set (or approximated).
On Linux, some non-standard baud rates are possible to achieve by using the Setserial system call and setting your baud rate to a special value.
The following class constants can be used to determine line state changes.
|LineCTS||Clear to send.|
|LineDCD||Data carrier detect.|
|LineDSR||Data set ready.|
|LineDTR||Data Terminal Ready|
|LineRTS||Request to Send|
The following class constants can be used to get or set the parity using the Parity property.
The following class constants can be used to get or set the number of stop bits using the Stop property.
|StopBits1||1 stop bit.|
|StopBits15||1.5 stop bits.|
|StopBits2||2 stop bits.|
The following class constants can be use to set the number of bits using the Bits property.
The following class constants can be used to test the LastErrorCode value.
|NoError||No error code.|
|PortNotFound||Port not found.|
|BreakCondition||Hardware detected a break condition. Usually due to a signal rate mismatch.|
|FramingError||Hardware detected a framing error. Occurs when the designated "start" and "stop" bits are not valid.|
Refer to this link for additional information on each error:
The Serial control can be used to communicate via multiple serial ports at once. You can use the properties of the System module to determine the number of serial ports on the computer and get an array of those ports. You should create an interface to allow the end user to choose the desired port, since serial ports are different on different machines and platforms.
When data is received by a serial port connection, the DataAvailable event handler will automatically execute. In this event handler, you would then use the Read or ReadAll functions to access the data in the serial port buffer. These functions remove the data from the serial port buffer as they return the data. If you need to read the data from the serial port buffer without removing it from the buffer, use the LookAhead property. This buffer will use as much memory as it needs from the memory available so there is no need for it to be resized.
Because the Write method is handled asynchronously, you may need to use the XmitWait method to force Real Studio to wait until Real Studio has finished sending the data out the serial port.
On Mac OS X and Linux, Real Studio gets exclusive rights to the serial port when opening it. This means that another application cannot also open the serial port after Real Studio has opened it, unless the user is running as root.
Communicating with USB Devices
Most USB devices have a chip in them that makes them appear as a serial device. Typically this chip is a FTDI chip. If the device has this chip, you can communicate with the device with the SerialPort class. If that does not work for you, the Monkeybread plug-in has USB support for a handful of specific types of devices.
The following code opens the serial port. It assumes that the Serial1 control has been added to a window.
MsgBox "The serial port is open."
MsgBox "The serial port could not be opened."
When the serial device sends data back to the Serial control that is open, the Serial control’s DataAvailable event fires. The data is transferred into a memory buffer. In the DataAvailable event handler, you use the Read or ReadAll methods to get some or all of the data from the buffer. Choose the Read method when you want to get a specific number of bytes (characters) from the buffer. Choose the ReadAll method to get all of the data in the buffer. In both cases, the data returned from the buffer is removed from the buffer to make room for more incoming data. If you need to examine the data in the buffer without removing it from the buffer, you can call the LookAhead method.
This example appends any incoming data to a TextArea.
Both the Read and ReadAll methods of the Serial class take an optional parameter that enables you to specify the encoding. Use the Encodings module to get the desired encoding and pass it as a parameter. For example, the code above has been modified to specify that the incoming text uses the ANSI encoding, a standard on Windows:
You can send data to the serial device at any time as long as you have opened the serial port with the Serial control’s Open method. You send data using the Serial control's Write method. The data you wish to send must be a string, as the Write method accepts only a string as a parameter.
MsgBox "The serial port could not be opened."
The Write method is performed asynchronously. This means that the next line of code following the Write method can already be executing before all the data has actually been sent to the serial device. If you need your code to wait for all data to be sent to the serial device before continuing, call the Serial control's XmitWait method immediately following a call to the Write method.
The following code directs the Serial control to communicate using Serial port zero (Modem port).
Watching for Line State Changes
You detect line state changes by passing an array or a ParamArray of line states that you want to watch. In the first instance, you can do it like this. The objects cCTS, cDTD, and so forth are checkboxes that the user sets to indicate which lines to watch.
' you want to watch.
Dim watchThese(-1) as Integer
If cCTS.Value then //checkbox for CTS..
If cDCD.Value then
If cDSR.Value then
If cDTR.Value then
If cRTS.Value then
If cRI.Value then
' Set the lines that we want to watch. Note
' that calling this function will clear any lines
' that we were watching previously, it doesn't
To use a ParamArray, you simply pass the class constants for the line states you want to watch. You don’t need to set up a real array.